- #APRICORN SATA WIRE 2.5 NOT RECOGNIZED FOR MAC#
- #APRICORN SATA WIRE 2.5 NOT RECOGNIZED MANUAL#
- #APRICORN SATA WIRE 2.5 NOT RECOGNIZED UPGRADE#
- #APRICORN SATA WIRE 2.5 NOT RECOGNIZED SOFTWARE#
- #APRICORN SATA WIRE 2.5 NOT RECOGNIZED WINDOWS 7#
Select the appropriate drive from the menu and click “Next” to continue. NOTE: Your computer’s internal drive will usually be denoted by the prefix AHCI or IDE. This is the drive you would like to copy from and in most cases is the internal drive in your notebook. Selecting the Source Drive Once EZ Gig has scanned for connected drives, you will be asked to select your Source Drive. EZ Gig will then scan for connected drives. Click the “Let’s Get Started” button to proceed.
#APRICORN SATA WIRE 2.5 NOT RECOGNIZED MANUAL#
If you have EZ Gig on a CD, please choose the Start option (proceed to page 11 of this manual to continue). EZ Gig Start Up Options Depending on how you received EZ Gig, you have two options.
#APRICORN SATA WIRE 2.5 NOT RECOGNIZED UPGRADE#
NOTE: The System BIOS controls basic hardware functions in computer, and is the first screen that appears when booting your computer (i.e.Ĭonnecting Your Hard Drive Before starting the EZ Gig software, please ensure that your new hard drive is connected to your notebook’s USB port via one of Apricorn’s Upgrade products listed on the previous page. To use Upgrade Suite as a stand-alone utility, your Computer must be able to boot from a CD-ROM, and the CD-ROM must be set as the first boot device in your computer’s System BIOS. Upgrade Suite (CD-ROM boot) Upgrade Suite CD is a bootable disk with EZ Gig data transfer utility that can copy hard drives without booting to the Windows operating system. When the User Account Control window pops up there will be a warning symbol and message that reads, “A program needs your permission to continue.” The instructions will read “If you started this program, Continue. The User Account Control window pops up in Administrator Approval Mode whenever a program tries to run on your Windows system.
#APRICORN SATA WIRE 2.5 NOT RECOGNIZED WINDOWS 7#
Although the steps below are not absolutely necessary to run EZ Gig, it’s best to try and clean-up disk errors BEFORE they are copied over to the new drive.ĮZ Gig instructions for Windows 7 & Vista Windows 7 and Vista User Account Control helps stop unauthorized changes to your computer. Most file system errors are not immediately obvious to the user, but can be identified and repaired with a few simple steps.
#APRICORN SATA WIRE 2.5 NOT RECOGNIZED SOFTWARE#
īefore Running the Software After many years of use, hard drives can become cluttered with unusable file fragments and other file-system errors.
If you are upgrading your Mac, please refer to page 27. Instructions for upgrading your Microsoft computer are provided on the following pages. Now you can upgrade your notebook drive using the Upgrade Suite CD. Simply connect your 2.5” SATA drive to the SATA Wire and connect the SATA Wire to your computer (shown in the figure below). The Package Contains Ĭonnecting your SATA Wire Device Installation Installing your SATA Wire is easy. With the help of Apricorn’s user-friendly cloning software, you can clone or backup your notebook drive in a snap.
Use it to connect any 2.5” SATA notebook hard drive to your computer. Getting to know your SATA Wire Introduction The SATA Wire is perfect for transferring data to bare drives.
#APRICORN SATA WIRE 2.5 NOT RECOGNIZED FOR MAC#
SharedMemory Animation HotCopy / LiveImage Avoid exclusive read access 20 20 21 21 Partitions 22 23 Start Clone 24 25 25 25 Congratulations your Clone is Complete 26 SuperDuper! Backup Software for Mac 27 After the Clone 28 28 29 SATA Wire FAQs 30 EZ Gig FAQs 33 Contacting Technical Support 38 38 39 Resizing your partitions manually Interupting the Cloning Process Aborting the Cloning Process Interupting the Verification process Using the SATA Wire as a ext TABLE OF CONTENTS Getting to know your SATA Wire 4 4 4 4 Connecting your SATA Wire 5 5 Before Running the Software 6 6 7 7 Upgrade Suite (CD-ROM boot) 8 8 9 Introduction The Package Contains System Requirements Device Installation Before running EZ Gig we recommend EZ Gig instructions for Windows 7 & Vista Changing the default “Power Options” To start EZ Gig directly from the CD-ROM Connecting Your Hard Drive EZ Gig Start Up Options 9 10 Cloning your hard drive with SATA Wire USB 2.0 to 2.5”SATA CONNECTOR User’s Guide Attention: If your SATA Wire shipped with a previous version of EZ Gig III, you can download the new EZ Gig IV from Apricorn’s website at: Review the most current SATA Wire FAQ’s at.